Hot tub owners in Portland OR have over the years been encouraged to remove or sell their spa baths that are not functioning properly. The process of unwanted hot tub removal is less complicated than the installation process. However, it is critical that you plan well prior to any removal efforts. The work involved is more or less half that of installation process.
You should assess the state in which your tub is in so that you decide whether to replace or repair it. It is because most removals have discovered catastrophic matters of maintenance and fixing. People in the cool areas are the most affected because they fail to winterize the tubs leading to water freezing in the pipes. Hence, it is important to first get to know the condition of the bath so that you judge which remedy action to take.
Rereading the manual is useful when it comes to removing your unwanted tub. This will juggle up your memory on the original construction of the plunge bath. You are supposed to have a full idea of how the electric wires are connected, how the heater was hooked up and so on. By doing so, you will not only ensure a successful removal but you will also be putting your own safety first.
Majority of these products are electric and some may have high voltage connections. Address electric service needs first before any removal efforts are made. There should be a main electrical disconnection box at close proximity to the hot tub. It the ideal location to isolate the electric power. In case it will not be replaced, it is advisable that you seal the outlet feed so as to leave it available for future re-installation.
During the actual action of removal, you will need to disconnect the electrical wires, disconnect the gas line and the heater. You are supposed to ensure that this step is safely conducted because electricity can be dangerous if improperly handled. Involved parties may be accidentally get shocked if there will be power running through the wires when you cut them.
After dealing with the electrical disconnection process, remove the spa skirt. Some whirlpools are manufactured using components connected using screws. This makes it possible for you to disassemble them using a screw driver. Some of the spa slats are connected together via the tongue and groove which do not require as much effort because their removal require no cutting.
Breaking the plunge pool floor is the most difficult part of removing an unwanted hot bath. The durable materials used in their production makes it quite difficult to cut them into smaller pieces. The most convenient tool to use to cut the spa bath is a jigsaw. You should make sure you are well geared up for the job because cutting may be very messy as a lot of dust is produced.
While cutting the plunge pool, you should cut it to pieces that can be conveniently be carried from the house to the outside. Dispose them properly in a dumpster. Before doing this, ensure that you protect yourself from any cuts by putting on gloves. Where safety eye covering to keep dust from getting into your eyes.
You should assess the state in which your tub is in so that you decide whether to replace or repair it. It is because most removals have discovered catastrophic matters of maintenance and fixing. People in the cool areas are the most affected because they fail to winterize the tubs leading to water freezing in the pipes. Hence, it is important to first get to know the condition of the bath so that you judge which remedy action to take.
Rereading the manual is useful when it comes to removing your unwanted tub. This will juggle up your memory on the original construction of the plunge bath. You are supposed to have a full idea of how the electric wires are connected, how the heater was hooked up and so on. By doing so, you will not only ensure a successful removal but you will also be putting your own safety first.
Majority of these products are electric and some may have high voltage connections. Address electric service needs first before any removal efforts are made. There should be a main electrical disconnection box at close proximity to the hot tub. It the ideal location to isolate the electric power. In case it will not be replaced, it is advisable that you seal the outlet feed so as to leave it available for future re-installation.
During the actual action of removal, you will need to disconnect the electrical wires, disconnect the gas line and the heater. You are supposed to ensure that this step is safely conducted because electricity can be dangerous if improperly handled. Involved parties may be accidentally get shocked if there will be power running through the wires when you cut them.
After dealing with the electrical disconnection process, remove the spa skirt. Some whirlpools are manufactured using components connected using screws. This makes it possible for you to disassemble them using a screw driver. Some of the spa slats are connected together via the tongue and groove which do not require as much effort because their removal require no cutting.
Breaking the plunge pool floor is the most difficult part of removing an unwanted hot bath. The durable materials used in their production makes it quite difficult to cut them into smaller pieces. The most convenient tool to use to cut the spa bath is a jigsaw. You should make sure you are well geared up for the job because cutting may be very messy as a lot of dust is produced.
While cutting the plunge pool, you should cut it to pieces that can be conveniently be carried from the house to the outside. Dispose them properly in a dumpster. Before doing this, ensure that you protect yourself from any cuts by putting on gloves. Where safety eye covering to keep dust from getting into your eyes.
About the Author:
If you are in need of information about unwanted hot tub removal, go to the web pages online here today. Additional details are available at http://www.nwspecialtymoving.com now.
Aucun commentaire:
Enregistrer un commentaire